Bosch DS7200V2-EXP Guia do Utilizador descarregar pdf (Página 50)

DS7200V2-EXP | Expert Programming Guide | 4. Control Panel Programming EN | 50

Bosch Security Systems | 8/04 | 4998153891C

Lock Area # Reporting

• Address:

− Area 1: 0297

− Area 2: 0319

− Area 3 (DS7240V2 only): 0341

− Area 4 (DS7240V2 only): 0363

• Default: 0 (Lock Area Disabled)

• Selections:

− 0 = Lock Area Disabled

− 1 = Lock Area Reports to Routing Destination 1

− 2 = Lock Area Reports to Routing Destination 2

This parameter locks area reporting to either Routing Destination 1 or Routing Destination 2. If you enable this

parameter for an area, all reports for that area are sent to the selected destination. Routing parameters for the

individual reports are ignored.

For example, if you set this parameter to 1, all reports in the area are sent to Destination 1. If you set this

parameter to 2, all reports in the area are sent to Destination 2.

Area Name Text

• Address:

− Area 1 Name: 1394 to 1425

− Area 2 Name: 1458 to 1489

− Area 3 Name (DS7240V2 only): 1522 to 1553

− Area 4 Name (DS7240V2 only): 1586 to 1617

• Default:

− Area 1: Area 1 Name Text

− Area 2: Area 2 Name Text

− Area 3 (DS7240V2 only): Area 3 Name Text

− Area 4 (DS7240V2 only): Area 4 Name Text

• Selections: See Key/Character selection chart

All control panel text is programmed from the text

keypad in a special text-programming mode. See Text

Entry Addresses on page 7 for text programming

instructions.

Enter up to 16 characters to describe each area.

Key Character

0 + - 0 * / \ [ ] = > < # §

1 Space . 1 ? ! , @ _ & ~ : ; " ( ) ' ¿ ¡ % £ $ ¥

2 A B C a b c 2 Å Ä Ã å ä á à â ã α β Ç ç

3 D E F d e f 3 É Æ ë é è ê æ ∆ Φ δ ε

4 G H I g h I 4 ï í î ì Γ γ η ι

5 J K L j k l 5 Λ κ λ

6 M N O m n o 6 Ö ö Ñ ñ Ø Õ ø ó ò ô õ Ω µ ν ω

7 P Q R S p q r s 7 Π Σ π ρ σ

8 T U V t u v 8 Ü ü ú ù û Θ Υ θ τ υ

9 W X Y Z w x y z 9 ÿ Ξ Ψ ξ χ ψ ζ

* Moves to the address before the text block.

# Moves to the address after the text block.

A Moves cursor to the previous character position in

text block.

C Moves cursor to the next character position in text

block.

The following keys are not used in text programming

and produce an error tone when pressed: [On], [Off],

[Perimeter Only], [No Entry], [Bypass], [System Reset],

and [B].

Press [1] once to clear a character space or to enter a

blank space.

1 2 ... 45 46 47 48 49 50 51 52 53 54 55 ... 155 156

Comentários a estes Manuais

Sem comentários

Bosch DS7200V2-EXP Guia do Utilizador Página 50

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Bosch DS7200V2-EXP