Bosch DS7200V2-EXP Guia do Utilizador descarregar pdf (Página 107)

DS7200V2-EXP | Expert Programming Guide | 4. Control Panel Programming EN | 107

Bosch Security Systems | 8/04 | 4998153891C

4.6 Output Parameters

4.6.1 Global Output Configuration

The DS7240V2 supports up to 20 outputs: four on-board Programmable Outputs (PO 1 to PO 4), and up to 16

off-board using two DX3010 Output Expanders. The DS7220V2 supports up to 12 outputs: four on-board

Programmable Outputs (PO 1 to PO 4), and up to 8 off-board using one DX3010 Output Expander.

Outputs 5 through 12 are on an off-board Data Bus device (DX3010 Output Expander or DX3020 X-10 Interface

Module) at Data Bus Address 150.

Outputs 13 through 20 (DS7240V2 only) are on an off-board Data Bus device (DX3010 Output Expander or

DX3020 X-10 Control Module) at Data Bus Address 151.

Global Output Options

• Address: 1039

• Default: 0

• Selections: 0 to 15

Enter This Data Digit to Select Options

Global Output Options 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

No Options Selected

•

Output 2 is Supervised Horn/Strobe Speaker Output

• • • • • • • •

Send Output Set/Reset Reports

• • • • • • • •

Enable Strobe Arming Flash to indicate RF Keyfob &

Keyswitch Arm/Disarm

• • • • • • • •

Enable Alarm Output Arming Beep to indicate RF

Keyfob & Keyswitch Arm/Disarm

• • • • • • • •

• Output 2 Is Supervised Horn/Speaker Output: This option turns Programmable Output 2 (PO 2) into a

supervised siren driver. If a siren or speaker is not connected, the control panel generates a Siren Trouble

event that can include a Siren Trouble {193} report. The restoral event is reported with Siren Trouble Restore

{194}. See “On-board Output Setup” in the DS7200V2 Installer’s Guide (P/N: 4998153893) for more

information. Compatible speakers include D118 and D119 Speaker Drivers.

• Send Output Set/Reset Reports: This option allows the control panel to send Output Set {109 to 111} and

Output Reset {106 to 108} reports when outputs are operated by a user, a Sked or RPS (Remote Programming

Software).

• Enable Strobe Arming Flash to Indicate RF Keyfob and Keyswitch Arm/Disarm: This option allows the

Strobe Output Function (1|6) to indicate RF and keyswitch arming and disarming as follows:

− 3 sec = transition to Off (disarmed)

− 6 sec = transition to All On or Perimeter Only

• Enable Alarm Output Arming Beep to Indicate RF Keyfob and Keyswitch Arm/Disarm: This option

allows any Alarm Output Functions (1|8, 1|9, 1|10, and 8|8) to indicate RF and Keyswitch arming and

disarming as follows:

− 1 Beep = transition to Off (disarmed)

− 2 Beeps = transition to All On

− 3 Beeps = transition to Perimeter Only

The “Enable Alarm Output Arming Beep to Indicate RF Keyfob and Keyswitch Arm/Disarm” option is

only available for RF Keyfobs (not RF Keypads) and when arming from RPS or a keyswitch.

1 2 ... 102 103 104 105 106 107 108 109 110 111 112 ... 155 156

Comentários a estes Manuais

Sem comentários

Bosch DS7200V2-EXP Guia do Utilizador Página 107

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Bosch DS7200V2-EXP