Bosch D7212GV2 Guia de Instalação Página 111
- Página / 140
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
D7212GV2 | Program Entry Guide | 5.0 RADXSKED EN | 111
Bosch Security Systems, Inc. | 1/08 | F01U003804-04
Default: Blank
Selection: 1 to 11, 13 to 24, 28, 29
S## Cmd Center
Default: Blank (0)
Selections: Blank (0), 1 to 8
Blank (0)
No keypad is
specified for
Custom Function
activation.
Identify the specific keypad
(CC #) where the Custom
Function is entered. Only one
keypad can be assigned for this
sked function.
1 to 8
Command center
(keypad) address
specified for
Custom Function
activation.
S## Custom Func
Default: Blank (0)
Blank (0)
No Custom
Function is
activated.
11 Execute Custom Func: This
function emulates any of the custom
functions assigned to the keypad that
can be executed by a user from the
keypad. When a sked executes a
custom function, it is subject to the
scope of the selected keypad.
Cmd
Center
and
Custom Func
prompts
appear after entering Function Code
11. Both entries are required.
Selections: Blank (0),
128 to 131 for D7212GV2
Enter the custom function this
sked executes.
128 to
131
Custom Function
to activate.
Avoid having multiple functions occur at the same time at the same address. Functions can clash and
the effect on the control panel is unpredictable.
Ensure that the Custom Function being executed or any of the commands nested inside the Custom
Function are not pass-code protected.
Do not program multiple skeds to execute at the same keypad during the same time.
Do not program skeds to execute at times when a user is likely to be executing functions at the keypad.
If it is necessary to do so, there are two ways to work around the situation:
1. Program CC at the beginning of the Custom Function Key Strokes entry. This aborts the user’s
function and allows the sked to execute.
2. Program the sked to execute at an address (Cmd Center) with no keypad physically attached to it.
The CC # must be assigned to an area and have the appropriate scope programmed.
Default: Blank
Selection: 1 to 11, 13 to 24, 28, 29
13 Adjust Time Forward One Hour: This sked function is used to make adjustments to the control panel’s
clock. A typical application is to program this to go into effect at 2:00 AM on the date that Daylight
Saving Time begins (during the springtime). No Time Change Report is sent or logged, but the new time
appears in the next report logged.
No other parameters require input for this option.
- D7212GV2 1
- System Requirements 2
- Trademarks 2
- Documentation Conventions 2
- Table of Contents 3
- 1.0 Introduction 5
- 1.2 Product Handlers 6
- 2.0 GV2MAIN 8
- 2.2 Phone Parameters 9
- Point/User Flag 10
- DTMF Dialing 11
- Phone Supv Time 11
- Alarm On Fail 11
- 2.3 Routing 12
- Route # 14
- R# Primary Device 14
- R# Backup Device 14
- View Events? 14
- R# Unverified Evt 15
- User Reports 16
- Test Reports 16
- Diag Reports 17
- Relay Reports 18
- AutoFunc Reports 18
- RPS Reports 18
- Point Reports 19
- User Chng Reports 19
- 2.4 Enhanced Routing 20
- RG1 Primary SDI 21
- RG1 Backup SDI 21
- [1234-001-011-008] 22
- 2.5 Power Supervision 25
- AC Fail Display 26
- AC Fail/Res Rpt 26
- AC Tag Along 26
- AC/Battery Buzz 26
- Bat Fail/Res Rpt 26
- 2.6 Printer Parameters 27
- 2.7 RPS Parameters 28
- RPS Passcode 29
- Log % Full 29
- RPS Call Back 29
- Answer Disarmed 30
- RPS Line Monitor 30
- Answer Armed 30
- 2.8 Miscellaneous 31
- 2.9 Area Parameters 31
- A# Area On 32
- A# Acct Number 32
- 22 33 44 5511 33
- 3 4 5 6 7 33
- A# Auto Watch 34
- A# Verify Time 34
- A# Duress Enable 35
- A# Area Type 36
- A# Exit Dly Time 37
- D## CC# Scope 37
- A# Fire Time 38
- A# Fire Pat 38
- A# Burg Time 39
- A# Burg Pat 39
- A# Single Ring 39
- A# Bell Test 39
- A# Area O/C 40
- A# Acct O/C 40
- A# Disable O/C in Window 41
- A# Auto Close 42
- A# Fail to Open 42
- A# Fail to Close 42
- A# Restrictd O/C 43
- A# Perimeter O/C 43
- A# Latest Close Time 43
- A# Two Man Rule 44
- A# Early Ambush 45
- A# Exit Restart 45
- A# Arm No Exit 46
- A# Exit Warning 46
- A# Entry Warning 46
- Cmd Center 47
- CC# Supervised 47
- CC# Area Assign 47
- CC# Scope 48
- CC# A1[through A4] in Scope 48
- CC# Entr Key Rly 48
- CC# Entr Cycl Dr 49
- CC# Assign Door 49
- CC# Trouble Tone 49
- CC# Entry Tone 49
- CC# Exit Tone 49
- CC# Arm Now Warn 50
- CC# Close Door 50
- CC# EnhancCmdCtr 50
- CC# Passcode Follows Scope 50
- CC# Scroll Lock 51
- CC# Menu Key Lock 51
- CC# Abort Display 51
- CC# Cancel Display 51
- Area# Is On 52
- Area# Not Ready 52
- Area# Is Off 52
- Area# Acct Is On 52
- Custom Function 53
- CF### Text 53
- CF### Key Strokes 53
- CF### Custom Function 54
- CF### Custom 54
- Function 54
- 2.11 User Interface 55
- Master Arm Delay 56
- Mstr Arm Inst 56
- Perim Instant 56
- Perim Delay 56
- P## Watch 57
- A # Watch Mode 57
- P## Type 1 58
- Expand Test Rpt 58
- Service Walk 61
- Default Text 61
- Change Skeds 61
- Invisible Walk Test 61
- C Function 128 [through 131] 61
- Authority Level 62
- L## Disarm 62
- L## Master Arm Delay 62
- L## Mstr Arm Inst 62
- L## Perim Instant 62
- P## Resettable 64
- L## Service Walk 67
- L## Default Text 67
- L## Change Skeds 67
- L## Invisible Walk Test 67
- A# Restrictd 68
- 2.12 Function List 69
- 2.13 Relay Parameters 70
- A# Alarm Bell 71
- A# Fire Bell 71
- A# Reset Sensors 72
- A# Force Armed 72
- A# Watch Mode 72
- A# Area Armed 72
- A# Area Fault 73
- A# Duress Relay 73
- A# Perim Fault 73
- A# Silent Alarm 73
- AC Fail Time 74
- P## Type 0 74
- P## Fire 74
- Summary Fire Tbl 75
- Summary SupFire 75
- Summary Trouble 75
- Summary SupBurg 75
- 3.0 RADXUSR1 76
- User ### 77
- U### Passcode 78
- U### User Group 78
- U### Name 78
- U### Mstr Site 78
- U### Mstr Crd Data 79
- U### SU1 through SU3 Site 79
- U### SU1 through SU3 C/D 79
- 4.0 RADXPNTS 80
- P## Ent Tone Off 81
- P## Entry Delay 81
- 4.2 Point Responses 84
- P## Pt Response 85
- P## Silent Bell 86
- P## Ring Til Rst 87
- P## Audible After 2 Failures 87
- P## Invisible Pt 87
- P## Buzz On Fault 88
- P## Watch Point 88
- P## RlyResp Type 89
- P## Disp as Dvc 89
- P## Local While Disarmed 89
- P## Local While Armed 90
- P## Disable Rst 90
- P## FA Retrnable 90
- P## BP Retrnable 90
- P## Bypassable 91
- P## Swinger Byps 91
- P## Defer BP Report 92
- P## Cross Point 92
- P## Fire Point 92
- P## Alarm Verify 93
- P## Alarm Abort 93
- 4.3 Point Assignments 94
- P### Debounce 95
- P### BFSK/Relay 95
- 4.4 COMMAND 7 and COMMAND 9 96
- CMD9 Point Index 97
- CMD9 BFSK/Relay 97
- CMD9 Point Text 97
- 5.0 RADXSKED 98
- W# Open Early Begin 99
- W# Open Window Start 100
- W# Open Window Stop 100
- W# Close Early Begin 101
- W# Close Window Start 102
- W# Close Window Stop 102
- Xept Holiday 103
- W# Xept Holiday 103
- User Windows # 105
- UW# User Group 105
- 5.2 Skeds 107
- S## Function Code 108
- S## Area # 109
- Relay Number 109
- Custom Func 111
- S## Cmd Center 112
- 5.3 Holiday Indexes 114
- Holiday Index 1 115
- 6.0 GV2AUX 116
- Parity/Stop 117
- 9133 Supervision 117
- RTS Control 117
- DTR Control 117
- Status Rate 117
- 6.4 SDI RPS Parameters 118
- 110.227.64.190 119
- RPS IP Address 2 120
- RPS IP Address 3 120
- RPS IP Address 4 120
- RPS Port Number 120
- CAUTION: 121
- WAR NIN G! 121
- Path # IP Add1 124
- Path # IP Add2 124
- Path # IP Add3 124
- Path # IP Add4 124
- Path # PortNum 125
- Path # Poll Rate 125
- Path # Ack Wait 126
- Path # Retry Count 127
- Path # Anti-Replay 127
- 6.6 SDI RPS/Enhanced 128
- Communications Configuration 128
- 6.7 Route Group Attempts 129
- 6.8 Miscellaneous 129
- Early Ambush Timer 130
- Secondary Ambush Code 130
- Abort Window 130
- Passcode Length 130
- Swinger Count 131
- Remote Warning 131
- CrystalTime Adj 131
- Perimeter Relay 131
- Early Armed Relay 131
- 6.9 Cross Point Parameters 132
- Programming Prompts Directory 134
- Bosch Security Systems, Inc 140
- 130 Perinton Parkway 140
- Fairport, NY 14450-9199 140
- (800) 289-0096 140
Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Bosch D7212GV2
(14 páginas)
(12 páginas)
(24 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.070 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais