Bosch B450 Guia de Instalação Página 94
- Página / 152
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Select this option to program a zone as silent. A silent zone does not activate the horn
speaker, bell, or strobe outputs. It activates the Silent Alarm output. The communicator and all
other programmable outputs function according to the parameters programmed for the zone.
8 – Sensor Watch
Sensor watch allows the control panel to recognize when detection devices might have
stopped working. This feature monitors the operation of a zone over the time period
programmed in Locations 476 and 477.
This value specifies how many 24-hour periods a zone can remain continuously sealed before
it registers as a Sensor Watch fault. The number of hours required to fulfill these 24-hour
periods is calculated only when the system is disarmed. Every time the system is armed in the
AWAY Mode, STAY Mode 1, or STAY Mode 2, the Sensor Watch Timer pauses its count. The
Sensor Watch Timer continues its count the next time the system is disarmed.
Example
If the Sensor Watch Time is programmed for 2 days and the premises is armed for 12 hours
and disarmed for 12 hours each day, it takes 4 days before a zone can register a Sensor Watch
fault.
Zone Options 2
This location has four programming options. You can select any combination of the options by
programming a single value. Calculate this value by adding the option bit numbers together.
Option Description
1 Isolate in STAY Mode 1
2 Zone Isolation Allowed
4 Forced Arming Allowed
8 Zone Restore Report
1 – Isolate in STAY Mode 1
If this option is selected, the zone can be automatically isolated when the system is armed in
STAY Mode 1.
If this option is not selected and the system is armed in STAY Mode 1, the zone activates an
alarm when activated as it normally would in AWAY Mode.
You can specify a global entry time for all zones, except for 24-Hour Zones, when the system is
armed in STAY Mode 1. You program this time in Locations 472 and 473. The Entry Guard
Timer overrides the delay time programmed for a Delay Zone. If you program the Entry Guard
Timer as 0, each zone acts according to its programmed zone type.
Refer to Arming the System in STAY Mode 1, page 53 for more information.
2 – Zone Isolation Allowed
If this option is selected, the operator can isolate the zone before arming the system. If this
option is not selected, the zone cannot be manually isolated. When a zone is manually
isolated, a Zone Bypass Report (Contact ID Event Code 570) is sent. Refer to Isolating zones,
page 56 for more information.
When isolating 24-Hour Zones, the system automatically sends a Zone Bypass Report when the
zone is selected to be isolated. All non-24-Hour zones send a Bypass Report only when the
system is armed.
4 – Forced Arming Allowed
9.3.6
94 en | Zone Information Control Panel
2014.07 | 00n | F01U298026 Installation Guide
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Bosch B450
(20 páginas)
(24 páginas)
(96 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais