Bosch B450 Guia de Instalação Página 132
- Página / 152
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Output Event Types
There are approximately 81 Output Event Types. Two numbers designate each Output Event
Type. Program these numbers into the appropriate locations for the output.
0,1 System Armed
This output operates when the system is armed. The output is reset when the system is
disarmed. If the system is partitioned, this output operates when both areas are armed in
AWAY Mode, STAY Mode 1 or STAY Mode 2.
0,2 System Disarmed
This output operates when the system is disarmed. The output is reset when the system is
armed. If the system is partitioned, this output operates when both areas are disarmed.
0,3 Armed in STAY Mode
This output operates when the system is armed in STAY Mode 1 or STAY Mode 2. The output is
reset when the system is disarmed. If the system is partitioned, this output operates when
either area is armed in STAY Mode 1 or STAY Mode 2.
0,4 Armed in AWAY Mode
This output operates when the system is armed in AWAY Mode. The output is reset when the
system is disarmed. If the system is partitioned, this output operates when either area is
armed in AWAY Mode.
0,5 Auto Arm Pre-Arming Alert Time
This output operates during the time period before the control panel is automatically armed in
AWAY Mode or STAY Mode 1. The output is reset when the control panel is automatically
armed in AWAY Mode or STAY Mode 1. The Auto Arming Pre-Alert Time is programmed in
Location 481.
0,6 Exit Warning with All Zones Sealed or Entry Warning
This output operates during Exit Time when the control panel is armed and all zones are
sealed. The output is reset when Exit Time expires.
This output operates again during Entry Time and is reset when Entry Time expires or the
system is disarmed.
This output also operates if a zone is activated when the system is armed in STAY Mode 1 or
STAY Mode 2 and the Entry Guard Timer for STAY Mode is programmed in Locations 472 and
473.
0,7 Exit Warning
This output operates during Exit Time when the system is armed. The output is reset when
Exit Time expires or the system is disarmed.
0,8 Exit Warning Finished
This output operates after Exit Time expires when the system is armed. The output is reset
when the system is disarmed.
0,9 Kiss-Off after Exit Time
This output operates after the first successful transmission to the base station receiver when
Exit Time expires. The output is reset when the system is disarmed.
0,11 Entry Warning
This output operates when during Entry Timer 1, Entry Timer 2, or Entry Guard Timer for STAY
Mode. The output is reset when the Entry Time or Entry Guard Time expires or the system is
disarmed. If Entry Time and Entry Guard time are present together, the output will follow the
Entry Guard Time.
0,12 Entry Warning + Day Alarm Resetting
This output combines Entry Warning and Day Alarm Resetting so that either of these two
events activates the output.
15.2
132 en | Programmable Outputs Control Panel
2014.07 | 00n | F01U298026 Installation Guide
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Bosch B450
(20 páginas)
(24 páginas)
(96 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.071 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais