Bosch B450 Guia de Instalação Página 60
- Página / 152
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
The codepad fault registers when any codepad is tampered or disconnected from the control
panel.
To determine which fault occurred, press the [7] key.
8 – Keyfob Low Battery
This fault occurs when any of the RF keyfobs report a low battery condition to the control
panel. To determine which keyfob failed, press the [8] key. Only keyfob 1 to 16 faults display
on the codepad through zone indicator 1 to 16.
System FAULT indicators
Indicator FAULT description
1 Low battery
This fault registers when the system detects a low capacity backup battery. The
system automatically performs a battery test every 4 hours and every time you
arm the system.
2 Date and time
This fault registers when the system is powered down.
3 RF receiver fault
This fault registers when the RF wireless receiver unit detects RF jamming, the
RF wireless receiver is disconnected from the control panel or failed, or the RF
receiver’s cover tamper switch is activated.
4 Warning Device fault
This fault registers when the system detects output 1-3 as warning device
(Horn Speaker, Siren Running, Strobe) is disconnected or short. This fault
clears once all outputs are reconnected. This feature is enabled by selecting
Option 2 in Location 492 (refer to System Options 1, page 106).
5 Telephone line fault
This fault registers when the system detects the telephone line is disconnected
from the control panel. This feature is enabled by selecting Option 1 in
Location 176.
7 Power Supply fail
This fault occurs when AUX power supplies fail, +12V power fails, or SDI2 Bus
power fails. Contact your installer as soon as this fault displays.
8 Onboard Tamper
This fault occurs when the system detects the control panel is tampered.
9-16 RF Repeater Tamper/Fail
The RF repeater 1 to 8 fault registers once the system detects that the wireless
repeater is disconnected or the repeater tamper is triggered.
AC MAINS Failure
An AC MAINS supply failure automatically flashes the MAINS indicator. If the AC MAINS supply
is disconnected continuously for longer than 2 min, the remote codepad beeps the codepad
buzzer once per min. If the control panel is programmed to report an AC MAINS failure to a
base station receiver, an AC Fail Report (Contact ID Event Code 301) is transmitted.
60
en | System Operations Control Panel
2014.07 | 00n | F01U298026 Installation Guide
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Bosch B450
(20 páginas)
(24 páginas)
(96 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.389 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais