Bosch B450 Guia de Instalação Página 35
- Página / 152
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
If this option is not selected, the installer can connect to a control panel from any remote
location for Upload/Download operations without the control panel calling back to the remote
computer. The user can initiate a modem call from the codepad by holding down [6].
4 – Exit from upload/download connection on alarmExit from upload/download connection
on alarm
If an alarm occurs when the control panel is communicating with a remote computer using A-
Link Plus, the A-Link session is terminated and the relevant alarm message is transmitted to
the base station receiver.
If an alarm occurs that does not have to be reported to the base station receiver, the session
is not terminated.
Communicating with the B426/B450
PC/A-Link Soluon 2000/3000 Panel
B426 -1 B450-2
SwitcherRouter
GPRS
Internet
The configuration diagram above is an example of using B426 as network module 1 and B450
as network module 2. The wiring diagram is shown in above picture. “B426-1” means the
rotary address switch of B426 is set to 1; “B450-2” means the rotary address switch of B450
is set to 2.
There are 9 steps to configure the communication platform of A-Link, B426, B450 and a
Solution 2000/3000 control panel from factory default values.
Install Tera term
Install Tera Term from the B450 CD. A-Link Plus is used to configure parameters of the control
panel and network module. Tera Term is used to access the USB menu of B450.
Program the module address using the codepad
1. Enter the Installer passcode (the default is 1234) and press [#] to enter Installer’s
Programming Mode.
2. Press [8][1] to access the Address Program menu.
3. To reset the parameters to default values, press [9][6][1][#] then press [9][6][0][#]. The
control panel returns to the main interface and restores all of the parameters to factory
default values.
4. Enter the Installer passcode (the default is 1234) and press [#] to enter Installer’s
Programming Mode. Press [7][2][1] to access the Network Module menu. Set the two
modules to 1 – Used, Not Config.
5. Continue to press [-] until you return to Confirm to Save Parameter Changes.
6. Press [#] to save changes.
Configure the B426 network module
4.9.3
Control Panel Accessories | en 35
Installation Guide 2014.07 | 00n | F01U298026
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Bosch B450
(20 páginas)
(24 páginas)
(96 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais