Bosch B450 Guia de Instalação Página 58
- Página / 152
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Two beeps sound and the system returns to the disarmed state.
The indicators for the selected zones continue to flash until the next time the system is
disarmed.
Example
To manually isolate zones 1, 3, and 4, press: [STAY][User Code][STAY][1][STAY][3][STAY][4]
[STAY][AWAY]
Fault analysis mode
When a system fault occurs, the FAULT or MAINS indicator flashes and the codepad beeps
once per minute.
If the AC MAINS supply fails, the MAINS indicator flashes until the AC MAINS supply is
restored. Press [AWAY] once to acknowledge the fault and stop the codepad from beeping
once every minute.
To enter Fault Analysis Mode to determine a system fault other than the AC MAINS supply:
1. Press and hold [5] until two beeps sound. The FAULT indicator remains lit and the STAY
and AWAY indicators flash. The lit zone indicators indicate the type of fault that occurred.
2. If necessary, press the button corresponding to the indicator to further determine the fault.
(Refer to the table Fault Analysis Conditions below.)
3. To exit from Fault Analysis Mode, press [AWAY]. The STAY and AWAY indicators are
extinguished and the FAULT indicator remains lit.
Fault Analysis Conditions
Zone
indicator
Fault description Button Zone
indicator
Fault condition
1 System fault 1 1 Low battery
2 Date and time
3 RF receiver jamming
RF receiver tamper switch
RF receiver communications fail
4 Warning device (output 1-3) fail
5 Telephone line fail
7 Power supply fail
8 On-board tamper
9-16 RF repeater fail
2 RF device low battery 2 1-16 Zones 1 to 16 RF low battery
3 Zone tamper alarm 3 1-16 Zones 1 to 16 tamper alarm
4 Sensor watch fail 4 1-16 Zones 1 to 16 sensor watch fail
5 RF sensor missing 5 1-16 Zones 1 to 16 RF sensor watch
fail
6 Communications fail 6 1 Receiver 1 fail
6.14
58 en | System Operations Control Panel
2014.07 | 00n | F01U298026 Installation Guide
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Bosch B450
(20 páginas)
(24 páginas)
(96 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.064 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais