Bosch B450 Guia de Instalação Página 64
- Página / 152
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
1. Enter the Installer Code and press [1][AWAY]. Three beeps sound and the STAY and AWAY
indicators flash.
2. Enter the number of days (1 to 15) and press [AWAY]. Two beeps sound and the STAY and
AWAY indicators are extinguished. The system returns to the disarmed state.
Change Domestic Phone Numbers
When the system is set up for domestic dialing, this function allows the installer to view and
program the telephone numbers the system calls if an alarm occurs. Refer to Domestic Dialing,
page 81 for more information.
To change domestic phone numbers:
1. Enter your passcode and press [2][AWAY]. Three beeps sound and the STAY and AWAY
indicators flash. There are 4 telephone number locations. Numbers 1 and 2 are for receiver 1.
Numbers 3 and 4 are for receiver 2. Press the sequence number to view and set/modify the
corresponding telephone number. If telephone numbers are programmed, they are displayed
one digit at a time using the remote codepad indicators. Refer to the table Domestic Dialing
Digits below for the indicators and their meanings.
If no telephone numbers are programmed, an additional two beeps sound after entering this
mode. These two beeps normally sound after you enter the last digit of the last phone
number.
2. Enter the first phone number. Each digit is displayed as you enter it. Press the [AWAY] to
save and exit from this mode.
4. Repeat steps 1 - 3 to program another phone number.
Domestic Dialing Digits
Digit required
Number to
program
Digit required Number to program
0 0 8 8
1 1 9 9
2 2
3 3 * [STAY]1
4 4 # [STAY]2
5 5 4 sec pause [STAY]3
6 6
7 7 15 [STAY]5
Example:
To program telephone numbers (96721777-primary and 96721233-backup) for receiver 1,
enter the following sequence:
[1234 2][AWAY][1][AWAY][9 6 7 2 1 7 7 7][AWAY][2 5 8 0 2][AWAY][2][AWAY] [4 9 6 7 21 2
3 3][AWAY]
You can cancel domestic dialing at any time (for example, you are moving and do not want the
system to continue calling your work place or mobile phone).
To disable domestic dialing:
7.1.3
64 en | System Functions Control Panel
2014.07 | 00n | F01U298026 Installation Guide
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Bosch B450
(20 páginas)
(24 páginas)
(96 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais