Bosch B450 Guia de Instalação Página 42
- Página / 152
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Configuration
Installer Commands
There are nine commands in Installer’s Programming Mode. To issue a command, enter the
command number and press [#].
Command Description
958 Exit from Installer’s Programming Mode without saving changes
959 Test IUI-SOL-ADAPTER
960 Exit from Installer’s Programming Mode with saving changes and system
reset
961 Reset the control panel to factory defaults
962 Copy the control panel memory to IUI-SOL-ADAPTER
963 Copy IUI-SOL-ADAPTER data to the control panel memory
965 Set up domestic dialing format
966 Enable/disable the automatic stepping of locations during programming
999 Display the software version number
Table 5.1: Installer’s Programming Commands
Command 958 - Exit from Installer's Programming Mode without saving
changes
This command exits from Installer’s Programming Mode. You can exit from Installer’s
Programming Mode from any location.
To exit from Installer’s Programming Mode:
Enter [9 6 0 #]. The system returns to the disarmed state. When using the remote codepad,
the STAY and AWAY indicators are extinguished.
Command 959 - Test the IUI-SOL-ADAPTER
This command initiates a test of the direct link adapter. You can only use the IUI-SOL-
ADAPTER Direct Link Adapter with the control panel.
The direct link adapter test is non-destructive, and any data in the direct link adapter remains
after the test is completed. One long beep indicates that the direct link adapter test failed.
Two beeps indicates a successful test.
If you remove the direct link adapter before the test is finished, the direct link adapter data
becomes corrupt. Do not remove the direct link adapter while the activity LED is lit or pulsing
rapidly.
To test the direct link adapter:
1. Enter the Installer Code (the default is 1234) and press [#] to enter Installer’s
Programming Mode. Two beeps sound and the STAY and AWAY indicators flash on the
remote codepad to indicate you entered Installer’s Programming Mode. The remote
codepad displays the data stored in Location 0000.
2. Connect the direct link adapter to the Bosch SDI2 Bus pins at the bottom of the control
panel printed circuit board.
5
5.1
5.1.1
5.1.2
42 en | Configuration Control Panel
2014.07 | 00n | F01U298026 Installation Guide
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Bosch B450
(20 páginas)
(24 páginas)
(96 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais