Bosch B450 Guia de Instalação Página 78
- Página / 152
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Arm the System in STAY Mode 1
Holding down [*] until two beeps sound arms the system in STAY Mode 1. This hold-down
function operates only if you select Option 2 in Location 497 (refer to Consumer Options 2,
page 109).
If there was no alarm during the armed cycle, holding down [*] a sec time disarms the system
from STAY Mode 1. To enable single button disarming from STAY Mode 1 using this hold-down
function, select Option 4 in Location 497.
If an alarm occurred or entry warning was activated, a valid User Code is required to disarm
the system.
Arm the System in STAY Mode 2
Holding down [0] until two beeps sound arms the system in STAY Mode 2. This hold-down
function operates only if you select Option 2 in Location 497 (refer to Consumer Options 2,
page 109).
If no sound alarm occurred during the armed cycle, holding down [0] a sec time disarms the
system from STAY Mode 2. To enable single button disarming from STAY Mode 2 using this
hold-down function, select Option 4 in Location 497.
If an alarm occurred or entry warning was activated, a valid User Code is required to disarm
the system.
Horn Speaker Test
Holding down [1] until two beeps sound activates the horn speaker for a 2-sec burst. No other
sounding device operates during this mode.
Bell Test
Holding down [2] until two beeps sound activates the internal screamers for a 2-sec burst. No
other sounding device operates during this mode.
Strobe Test
Holding down [3] operates the strobe. No other device operates during this mode.
To turn the strobe test on:
Press and hold [3] until three beeps sound. The strobe flashes.
To turn the strobe test off:
Press and hold [3] until two beeps sound. The strobe stops flashing.
Turning Day Alarm On and Off
Holding down [4] turns Day Alarm on or off. If you want the STAY indicator to indicate the
status of Day Alarm operation (enabled or disabled), select Option 8 in Location 496 (refer to
Consumer Options 1, page 108). When this option is selected, the STAY indicator flashes once
every 3 sec when Day Alarm is active.
To turn Day Alarm on:
Press and hold [4] until three beeps sound.
To turn Day Alarm off:
Press and hold [4] until two beeps sound.
7.4.2
7.4.3
7.4.4
7.4.5
7.4.6
7.4.7
78 en | System Functions Control Panel
2014.07 | 00n | F01U298026 Installation Guide
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Bosch B450
(20 páginas)
(24 páginas)
(96 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.080 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais