Bosch DS7400XiV4-EXP Especificações descarregar pdf (Página 112)

DS7400XiV4-EXP | Reference Guide | 7. Reference Materials EN | 112

Bosch Security Systems | 1/05| 4998154963B

Entry/Exit Delay Cancel Zone Functions: Entry/Exit

Delay Cancel 1 and Entry/Exit Delay Cancel 2 Zone

Functions cause the exit delay to expire as soon as the

premises is vacated.

• If a zone is programmed as an Entry/Exit Delay

Cancel zone, and it is activated during the exit

delay, the exit delay will expire as soon as the zone

has been restored.

• Entry/Exit Delay Cancel 1 follows entry delay 1.

• Entry/Exit Delay Cancel 2 follows entry delay 2.

Interior Entry/Exit Follower: This is a zone

programmed to be ignored during an entry/exit delay

and then become an interior instant zone.

• If this zone is violated while the system is armed

and no entry/exit zones have been violated, it will

activate an alarm.

• If this zone is violated after an entry/exit delay

zone is violated, it will follow that entry/exit delay

time.

• This zone is bypassed by Perimeter Instant or

Perimeter arming.

Interior Home/Away: This is a zone programmed to

become an interior instant zone if the system is armed

and an entry/exit delay zone is violated during the exit

delay time.

• If the system is armed and an entry/exit delay zone

is not violated, this zone will be bypassed.

• This zone is bypassed by Perimeter Instant or

Perimeter arming.

Interior Instant: This is a zone programmed to activate

an alarm even during the entry/exit delay periods.

• It is bypassed by Perimeter Instant or Perimeter

arming.

Day Monitor: This is a zone programmed to be a

perimeter instant zone when the system is armed.

• When the system is disarmed, any violation of this

zone will activate the keypad sounders which will

sound continuously until a disarm command

sequence is entered.

• The alarm outputs for this zone will not activate

and there will be no report for this zone when the

system is disarmed.

Keyswitch Input: This is a zone programmed to allow

the system to be armed or disarmed using a Normally

Open momentary keyswitch.

• Outputs for keyswitch LEDs and sounders are

available using the programmable outputs or the

Octal relay outputs.

• An output is needed for each LED and sounder.

• A keyswitch will only control the area that these

zones are assigned to unless programmed as a

master, then it will control all at once. See

Program Address 0001, Data Digit 1.

• Keyswitches and keypads may be used in the same

area, if desired.

Fire Zone: This is a zone programmed to activate if

the system is armed or disarmed.

• It can be silenced (not reset) by entering a valid

[PIN][Off].

• The display will indicate a Fire Alarm for this zone

on all keypads in every area.

• A fire reset command must be entered after

silencing the alarm to re-enable this zone.

• If this zone is programmed for trouble and the

loop opens, the DS7447E/DS7447V2 keypad will

display "Fire Trouble" for this zone and the

keypad sounders will beep once every ten

seconds.

• If the system is a combination fire and burglar

alarm, the fire alarm has priority over the burglar

alarm.

Fire Zone with Verification: This zone is identical to

a Fire Zone except that after the first alarm, it will

perform a fire reset and then wait up to two minutes

for a second alarm.

• If a second alarm occurs within this two minute

period, the system will indicate a fire alarm.

• If there is no second alarm within this two minute

period, the control panel will reset back to its

normal condition.

1 2 ... 107 108 109 110 111 112 113 114 115 116 117 ... 143 144

Comentários a estes Manuais

Sem comentários

Bosch DS7400XiV4-EXP Especificações Página 112

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Bosch DS7400XiV4-EXP