Bosch LTC 2604 Manual de Instruções descarregar pdf (Página 14)

IntuiKey Series | Instruction Manual | Selceting a Device for Control

Bosch Security Systems | 28 June 2004

IMPORTANT: When the IntuiKey is first connected

up to a device, or whenever a new video device is

added to an existing system, enter the Product Selection

menu and press the PROD key. The keyboard will

initiate a scan of the communication lines and update

the list of devices connected to it.

If communication is ever lost with an existing device,

the product name display will indicate an Off_Line

condition. After communication with the device is

restored, this message will disappear.

For multiplexers, the device address number will be

shown. For DVRs, the DVR address number, its name,

and the starting camera offset number will be displayed.

3.2.3 Selecting a Device for Control

1. Press the PROD button to put the keyboard in the

Product Selection Mode. The softkey display shows

the Product Selection menu (refer to FIGURE 3-2).

2. Press the desired softkey button adjacent to the

desired product name in the display. Upon

selection of a system device to be controlled, the

keyboard indicates what product it is controlling

by displaying its name (up to 10 characters

maximum) at the bottom of the status display. The

softkey display menu also changes to the top level

menu associated with the selected device.

3.2.4 Easy Switching Between Devices

Pressing and holding the PROD key for longer than

1 second while using a DVR or multiplexer enters the

device address selection mode. Entering the address of a

device will cause the keyboard to switch to that device’s

main menu. If the device address does not exist, an error

message will result, and no change will occur.

3.2.5 Using the Keypad for Numeric Entry

(Camera Control)

1. Press a desired numeric key to place the number in

the status display under the camera title.

2. Note that additional key entries add digits to the

RIGHT side of the camera number. If more than

the maximum number of digits allowed for the

specific entry is entered, the leftmost digit is lost,

and all other digits promoted.

3. Leading zeros may be entered but are not required.

4. Press ENTER to complete numeric entry.

3.2.6 Using the Quick Selection Softscreen Feature

The IntuiKey softkey display screens can be assigned a

reference number which can then be recalled to

quickly return to the desired screen.

1. To assign a number to a softkey display screen, first

navigate to the desired screen. Simultaneously press

the digit 0 and ENTER to enter the softkey screen

programming mode. Press SHOT followed by the

single digit (0 to 9) that you want to assign to this

screen.

2. To quickly jump to a previously programmed

softkey display screen, simultaneously press the

digit 0 and ENTER. Press the desired softkey

display screen number.

NOTE: Ten (10) softkey numbers are available within

a single product category. Softkey screen numbers can

only jump between screens within the same product

category. If an existing softkey screen number is

assigned to a new softkey screen, the old one is no

longer valid. Assignments remain even if power is lost.

3.3 Alarm/Alert/Action Indication

When the IntuiKey detects that an alarm/alert/action

condition has occurred on the presently controlled

device, the key flashes red and an audible tone is

heard. During alarm responses, Divar DVRs and

System4 multiplexers will also show special icons to

represent the different types of alarm conditions.

Contact type alarm conditions will be represented by

a icon, and action alarm conditions will be

represented by a icon.

If the alert occurs on a device that is not presently

under control, the product indicator (in the status

display) alternates between the present product

designator and the alarmed product, with the text

ALERT added. The present product is displayed for

two seconds, while the alarmed product is displayed

for 0.5 seconds.

3.4 Configuring the IntuiKey Keyboard

The IntuiKey Keyboard plug and play design allows

operation to begin as soon as the keyboard is

connected to system components. However, if you

desire to review the default settings, or wish to change

any of these settings, refer to the following information

and procedures for the Keyboard Control Mode.

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 47 48

Comentários a estes Manuais

Sem comentários

Bosch LTC 2604 Manual de Instruções Página 14

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Bosch LTC 2604