Bosch K2200 Series Guia de Instalação descarregar pdf (Página 50)

K2200 Series | Installation Guide | 6.0 Configuration and Testing EN | 50

Bosch Security Systems | 7/03 | 17375 1.3 / 46513C

ENTER TIME 15-53

Press [ENT] to save.

End of process. Press [ESC] to go back to the CMD

prompt.

The DL Command

The Download (DL) command sends the contents of

the master controller's database to all slave

controllers. This will ensure that all the door

controllers have the same information. (The slave

controllers need to be configured and address

properly in order for this command to function).

1. At the CMD prompt, type [D][L] and press [ENT].

CMD DL

2. Type [Y] and press [ENT] to confirm.

DLOAD TO ALL Y

3. From the CMD prompt, press the ESC key to exit

out of programming.

CMD_

4. You will see this message on the screen when

you leave programming mode.

SENDING DATA

It indicates the progress of the download, in this

example 26.9%. The download will be complete

when it reaches 100%. The message will

disappear when the download is completed.

DOWNLOAD 26-9

6.1.10 Testing Readers and Locks

If you programmed a master programming key in the

INST command, that key will have access through all

doors. You can now use this key to check the

operation of readers and locks.

Readers

1. Present the key to each reader:

2. The green LED should light on the reader and

remain on for the duration of the lock release

time.

3. The lock should operate for the duration of the

lock release time.

4. The faceplate should display the following (the

numbers indicating which doors are open):

DOORS OPEN 1

Door Monitoring

If door monitoring is being used:

1. Close the door before the lock release time

expires, the green LED on the reader should go

out and the door should lock.

2. Leave the door open after a valid card read, the

green LED on the reader will go out and the lock

will lock. After the expiry of the door open time,

you should get a door left open warning:

CH 1 – O --------

3. Open the door without presenting a key or

tripping the request to exit device. You should

immediately obtain a door alarm, flashing and

sounding, indicating which door has been forced:

DOOR 01 ALARM

4. You should get exactly the same effect by

disconnecting the reader terminal block - causing

a tamper alarm.

Note:

To silence the faceplate, present the Master

programming key to the faceplate reader

6.2 RS-232 Serial Port

The RS-232 serial port can be used to connect the

door controller to a variety of devices.

Note:

The printer connector is not currently used. The printer

is connected via the RS-232 connector.

6.2.1 Connecting a Printer

Faceplate:

A printer can only be fitted when the system is being

administered from the faceplate. When administered

from a PC, all printed output is generated by the PC.

Report Printing

All the information stored in the door controller

database can be printed. There are several printer

commands, P1 to P9, see Readykey

K2200 Series

Controllers User Guide (Bosch P/N: 47491, PAC P/N:

17376), which will allow particular reports to be

generated.

Transaction Printing

The door controller can store about 2400 transactions

in its memory. Each transaction is printed out if a

printer is connected. If the printer is not connected,

the transactions will be stored. Once the maximum

number of transactions is reached, the oldest ones

will be lost. When the printer is reconnected, printing

will continue with the oldest unprinted transaction

and continue until all unprinted transactions have

been output.

1 2 ... 45 46 47 48 49 50 51 52 53 54 55 ... 59 60

Comentários a estes Manuais

Sem comentários

Bosch K2200 Series Guia de Instalação Página 50

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Bosch K2200 Series