Bosch K2200 Series Guia de Instalação descarregar pdf (Página 47)

K2200 Series | Installation Guide | 6.0 Configuration and Testing EN | 47

Bosch Security Systems | 7/03 | 17375 1.3 / 46513C

For example, if you want a dial-back to be

initiated when a positive event occurs on doors 1

and 3 on door controller 1, type 1 and 3 and

press [ENT].

Press [ENT] to save, press [NXT] go on.

8. This allows programming of positive event dial-

back for door controller 2 (i.e. the controller with

address 2)

DIAL D/C2 DR----

Programming is identical to that for door

controller 1.

Press [ENT] to save, press [NXT] go on.

9. This allows programming of positive event dial-

back for door controller 3

DIAL D/C3 DR----

Programming is identical to that for door

controller 1.

Press [ENT] to save, press [NXT] go on.

10. This allows programming of positive event dial-

back for door controller 4

DIAL D/C4 DR----

Programming is identical to door controller 1.

Press [ENT] to save, press [NXT] go on.

11. This allows programming of positive event dial-

back for door controller 5

DIAL D/C5 DR----

Programming is identical for door controller 1.

Press [ENT] to save, press [NXT] go on.

12. This allows programming of positive event dial-

back for door controller 6

DIAL D/C6 DR----

Programming is identical for door controller 1.

Press [ENT] to save, press [NXT] go on.

13. This allows programming of positive event dial-

back for door controller 7

DIAL D/C7 DR----

Programming is identical for door controller 1.

Press [ENT] to save, press [NXT] go on.

14. This allows programming of positive event dial-

back for door controller 8.

DIAL D/C8 DR----

Programming is identical for door controller 1.

Press [ENT] to save, press [NXT] go on.

Note:

In order for dial-back on positive events to operate a

number of other settings need to be programmed.

Setting

mode, the following must be programmed:

CONNECT MODEM Y

Make sure that Y is programmed to indicate there is a

dial-up modem connected to this door controller.

SETUP –D------

Make sure that the D setting is programmed here to

enable

Dialback

. In the event of an alarm condition,

the door controller will dial-back to the Multi-Site

CNC. If a dial-back on positive transactions is also

required, the additional settings described above must

also be programmed.

EVENT

mode

the following must be programmed:

FRGT POS TRANS N

This setting must be programmed to N in order that all

positive transactions are not ignored, and hence initiate

dial-back to the CNC.

6.1.9 Programming Readers and Locks (For

Standalone Masters only, no software)

Having verified the operation of the readers and door

inputs, now you can verify the lock operation. To do

this you will need to program some values against

each door.

Note:

As these will be required when the system is

operational, it is sensible to use the correct information

for each door.

Get to the CMD prompt by presenting the master key

to the internal reader on the controller faceplate.

The D Command

This command allows settings to be made for each

door. You can use the up and down arrow keys to

move between doors (the door number DR n will

change). Use the [NXT] and - (minus) keys to move

between settings.

1. At the CMD prompt, type [D] and press [ENT].

CMD D

If you get an PC ADMIN ACTIVE message, you

will need to change PC ADMIN ACTIVE to [N]

to continue.

2. This is the number of seconds for which the lock

will operate. Type the required number of

seconds for the Door 1, Lock Release Time . (0-

255 seconds).

DR 1 LRT 5

Press [ENT] to save, [NXT] to go on.

3. Type the required number of seconds for the

Door 1, Door Open Time. (0-255 seconds).

DR 1 DOT 0

This is the amount of time, in seconds, after the

lock release time has expired, at which a door

left open warning will be given.

1 2 ... 42 43 44 45 46 47 48 49 50 51 52 ... 59 60

Comentários a estes Manuais

Sem comentários

Bosch K2200 Series Guia de Instalação Página 47

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Bosch K2200 Series