DS7400XiV4-EXP
DS7400XiV4-EXP Release Notes
© 2005 Bosch Security Systems Page 4 4998154793B
2.1.9 Programming Baud Rate for Network
Communication
If the Network Communication Module is enabled,
you must also configure its baud rate.
DX4020 Network Interface Module:
Configure Addresses 4020 for Module 1
and 3042 if using Module 2 as 4 1. Refer
to Table 8 and Table 9 on page 4. Also
configure Addresses 4019 and 3041 as
1 0. Refer to Section 2.1.10 Programming
Modules 1 and 2 for RS-232 Printing on
page 4.
RPS Direct Connection option for
programming using Module 1: Configure
Address 4019 as 1 0, and configure
Address 4020 as 2 5. Refer to Table 8
and Table 9 on page 4.
Remote Programming is only available
through Network Communication Module
1.
• Addresses: 4020 (Module 1); 3042 (Module 2)
• Data Digit:
• Data Digit 1: ____ (refer to Table 8;
default = 0)
• Data Digit 2: ____ (refer to Table 9;
default = 0)
• Selections: 0 to 5 for Data Digit 1; 0 to 7 for Data
Digit 2
Table 8: Module 1 and 2 Baud Rate, Data Digit 1
Select Option Value
300 baud
0
1200 baud 1
2400 baud 2
4800 baud 3
9600 baud 4
14400 baud 5
Table 9: Parity, Flow Control, Stop Bits, and
Data Bits Configuration, Data Digit 2
Select Options 0 1 2 3 4 5 6 7
No Parity
• • • •
ODD Parity
• •
EVEN Parity
• •
Software Flow
Control
•
•
•
•
Hardware Flow
Control
•
•
•
•
1 Stop Bit
• •
• • • •
2 Stop Bits
• •
8 Data Bits
• • • •
• • • •
2.1.10 Programming Modules 1 and 2 for RS-232
Printing
You can use Module 1 or 2 to connect the control
panel to an RS-232 printer. Most printers operate
using the default values, but some printers operate
more efficiently using optional program values. Refer
to Section 2.1.11 RS-232 Printer Baud Rate Programming
for baud rate configuration.
Consult the operating guide provided with your
printer to ensure that its configuration matches the
one programmed here.
• Addresses: 4019 (Module 1); 3041 (Module 2)
• Data Digit:
• Data Digit 1: ____ (refer to Table 10;
default = 0)
• Data Digit 2: ____ (refer to Table 11;
default = 7)
• Selections: 0 or 1 for Data Digit 1; 0 through 7
for Data Digit 2
Table 10: RS-232 Printing Using Module 1 and 2
Select Option Value
Module disabled
0
Module enabled for printing 1
Table 11: RS-232 Event Printing Configuration,
Data Digit 2
Select Options 0 1 2 3 4 5 6 7
No Events
•
Alarms, Troubles,
and Restorals
•
•
•
•
Opens and Closes
• •
• •
All Other Events
• • • •
(54 páginas)
(123 páginas)
(16 páginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais