
D9412GV3/D7412GV3 | Operation and Installation Guide | Federal Communications Commission
6 Bosch Security Systems, Inc. | 2/10 | F01U143070-01
Two telco lines: ..............................................................75
Discharge Cycle.............................................................75
Figures
Figure 1: System Configuration ..............................10
Figure 2: Enclosure Mounting .................................16
Figure 3: Ground Fault DetectionError! Bookmark
not defined.
Figure 4: Enabling Ground Fault Detection...........17
Figure 5: Reset Pin ...................................................18
Figure 6: D9412GV3 Service Walk Test Flow
Chart...........................................................21
Figure 7: D7412GV3 Service Walk Test Flow
Chart...........................................................22
Figure 8: Non-Power-Limited Wiring...............Error!
Bookmark not defined.
Figure 9: Charging and Battery LEDs ....................25
Figure 10: RJ31X Wiring ............................................29
Figure 11: Phone Connector, Phone LED, and
Operation Monitor LED Locations..........30
Figure 12: D928 Dual Phone Line Switcher ............32
Figure 13: On-board Point Sensor Loop Wiring .....34
Figure 14: Rothenbuhler 5110/4001-42 High
Security Bell Wiring Configuration .........36
Figure 15: Wiring the Rothenbuhler 5110/4001-42
High Security Bell to the D9412GV3 or
D7412GV3 Control Panel........................37
Figure 16: Connecting the D8125 POPEX to
the D9412GV3 Control Panel.................40
Figure 17: Connecting the D8125 POPEX to
the D7412GV3 Control Panel.................41
Figure 18: Program Record Sheet............................44
Figure 19: D8128D OctoPOPIT Layout ...................45
Figure 20: Connecting D8128D OctoPOPITs to
the D9412GV3 ..........................................48
Figure 21: Connecting D8128D OctoPOPITs to
the D7412GV3 ..........................................49
Figure 22: Wiring Multiple D8128Ds Using Molex
®
Connectors ................................................50
Figure 23: D8128D OctoPOPIT Sensor Loops.......51
Figure 24: D8129 Connections to the D9412GV3..52
Figure 25: D8129 Connections to the D7412GV3..53
Figure 26: D811 Module Wiring to the D9412GV3.55
Figure 27: D811 Module Wiring to the
D7412GV3.................................................56
Figure 28: Power at Keypads ....................................59
Figure 29: Keyswitch Wiring ......................................61
Figure 32: DX4020 DIP Switch Settings ..................63
Figure 33: Reset Pin ...................................................64
Figure 34: Programmer and Accessory
Connections..............................................64
Figure 35: D9412GV3 Faceplate..............................65
Figure 36: D7412GV3 Faceplate..............................66
Figure 37: D9412GV3, Power Supply Side.............67
Figure 38: D9412GV3, Input Points and
Peripheral Devices................................... 68
Figure 39: D9412GV3, SDI Devices ........................ 69
Figure 40: D7412GV3, Power Supply Side.............70
Figure 41: D7412GV3, Input Points and
Peripheral Devices................................... 71
Figure 42: D7412GV3, SDI Devices ........................ 72
Tables
Table 1: Related Documentation............................. 8
Table 2: GV3 Series Control Panel Differences .10
Table 3: Compatible Accessories
1
........................11
Table 4: Software Version Compatibility of
D6500 MPU and Line Cards .................. 14
Table 5: Compatible Keypads and Command
Centers ......................................................14
Table 6: Ground Fault Impedance
Specifications............................................17
Table 7: Battery Discharge and Recharge
Schedule....................................................26
Table 8: Charging Status and Low Battery
LEDs .......................................................... 26
Table 9: Phone Cord Lengths................................ 33
Table 10: Point Parameters .....................................34
Table 11: POPEX Modules ......................................38
Table 12: Extra Point Events ...................................38
Table 13: Off-Board Point Errors............................. 39
Table 14: Data Expansion Loop Wire
Specifications............................................42
Table 15: D8128D OctoPOPIT Switch Settings
for D9412GV3 and D7412GV3 ..............46
Table 16: Switch 5 Settings for Line Termination .46
Table 17: Terminal Strip Connections ....................47
Table 18: D8129 OctoRelay Switch Settings.........53
Table 19: Number of D8128Ds Used with
D8129s ...................................................... 54
Table 20: Keypad Address Settings........................57
Table 21: Keypad Connections ............................... 58
Table 22: SDI Device Connections......................... 62
Table 23: Printer Address Switch Settings.............62
Table 24: Address Switch Settings for Access
Control Module ......................................... 63
Table 25: Zonex 1 Point Address Chart .................73
Comentários a estes Manuais