Bosch GST 85 P Instruções de Operação descarregar pdf (Página 9)

English - 4

GST 85 PAE: Remove the cover guard 12 and

open the slider 22 at the bottom side of the base

plate.

After loosening the screw 15 and sliding lightly

forward in the direction of the saw blade, the base

plate 8 can be swung to the right or left to a max-

imum of 45°.

After coarse adjustment, tighten the screw 15 so

that the base plate 8 can still just be adjusted.

The cutting angle can be pre-adjusted by means

of the scale for mitre angles 14. Precise adjust-

ment with use of a commercial angle gauge 16 is

recommended.

Then tighten the screw 15 again.

To achieve precise cutting angles, the base plate

is fitted with a locking device at 0° and 45° (left

and right). For this, however, the base plate must

be pushed back (towards the motor) to the stop,

so that the notch in the base plate engages in the

positioning pin 18.

When returning the base plate to the 0° (normal)

position, press the base plate lightly in the direc-

tion of the motor until it can be felt to engage and

again tighten the screw 15.

For sawing close to edges, the base plate can be

offset to the rear:

GST 85 PAE: Remove the cover guard 12 and

open the slider 22 at the bottom side of the base

plate.

Use Allen key 3 to take out screw 15 completely.

Lift the base plate and move it to the rear such

that the screw can be turned into the rear thread.

When tightening the screw 15, the base plate

must be pressed to the rear until it can be felt to

engage.

– With the base plate offset, only the 0° (normal)

position can be used.

– The circle cutter/parallel guide 23 as well as

the splinter guard 19 cannot be used in this

case.

The base plate 8 is originally equipped with a re-

placeable base-plate cover 21 made of plastic. It

ensures good sliding capability on wood and

plastic surfaces, and largely avoids scratching of

sensitive surfaces.

After loosening the six screws 20, the replacea-

ble plastic base-plate cover can be exchanged

against a steel insert, which is intended for use

on metal surfaces.

To avoid fraying of the surface, install the splinter

guard 19 by pressing it into the base plate 8.

The splinter guard cannot be used for certain saw

blade types (e. g., saw blades with set teeth).

The machine can be plugged directly into the re-

ceptacle of a Bosch all-purpose vacuum cleaner

with remote starting control. The vacuum cleaner

starts automatically when the machine is

switched on.

The vacuum cleaner must be suitable for the ma-

terial to be worked.

When vacuuming dry dust that is especially detri-

mental to health or carcinogenic, use a special

vacuum cleaner.

For external dust extraction with a vacuum

cleaner, an extraction adapter must be used as

required (see accessories). Insert extraction

adapter and vacuum connection firmly.

Attach the vacuum connection 5 to the base

plate 8 and connect the extraction hose.

For low blowing effect, set the sawdust blower

switch 6 upward.

Cover Guard

The transparent cover guard 12 enables the col-

lection of chips and sawdust. To achieve opti-

mum results, it must always be mounted when

working with dust extraction.

Adjusting the Cutting Angle

(see figure )

Offsetting the Base Plate

(see figure )

Replaceable Base-plate Covers

(GST 85 PAE – see figure )

Splinter Guard (see figure )

Dust/Chip Extraction

(GST 85 PAE)

2 609 931 878.book Seite 4 Donnerstag, 4. November 2004 8:06 08

15 • 2 609 931 878 • TMS • 27.10.04

1 2 3 4 5 6 7 8 9 10 11 12

Comentários a estes Manuais

Sem comentários

Bosch GST 85 P Instruções de Operação Página 9

Comentários a estes Manuais

Manuais e produtos relacionados com Ferramentas elétricas Bosch GST 85 P