Bosch D9210C Manual do Utilizador descarregar pdf (Página 3)

GV4 Series Control Panel | Release Notes

3 Bosch Security Systems, Inc. | 11/11 | F01U261045-01

1.0 Requirements

Table 1: Supporting Literature for GV4

Series with Firmware Version 1.00

and Later

Description Part Number

D9412GV4/D7412GV4/D7212GV4

Program Entry Guide

F01U218312

D9412GV4/D7412GV4/D7212GV4

Program Record Sheet

F01U214958

D9412GV4/D7412GV4/D7212GV4

Operation and Installation Guide

F01U201527

D9412GV4/D7412GV4/D7212GV4

Approved Applications Compliance Guide

F01U201525

D9412GV4/D7412GV4/D7212GV4 UL

Installation Guide

F01U215246

Use Remote Programming Software

(RPS) version 5.14 and later with this

software version.

The D5200 Programmer is not supported

by the GV4 Series control panel.

The D5360 Direct Connect Module is not

supported by the GV4 Series control

panel.

A limited programmers menu is available

from the Service menu on the keypad.

2.0 Firmware Revision History

2.1 GV4 Version 1.00

2.1.1 Remote Firmware Update

 GV4 Series control panels include the support

of remote firmware updating via v5.14 or

later. Only the panel firmware can be updated

remotely. The control panel is not operational

during firmware updates. All RPS connections

are considered remote connections.

Local Authorization for Remote Firmware

Updat

e

 GV4 Series control panels include support for

a control panel option to require local

authorization for a remote firmware upgrade.

This option is modified via RPS only.

 When the local authorization option is

enabled, only a user with the Firmware

Update Authority enabled can authorize the

update.

 The Firmware Update Authorization command

is in option in the Service menu (9-9-Ent). The

Service menu is available from any text

keypad.

 Firmware Update Authorization can only be

granted when the control panel is in an active

RPS session via the network.

 Once Firmware Update Authorization is

granted, RPS disconnects and the control

panel begins the update.

Preconditions

 When

the Reset Switch option is enabled, and

the local authorization is required, the control

panel will not update the firmware until local

authorization is granted (no troubles).

 The panel must be running normally, AC

Power must be present, and the battery fully

charged. Firmware updates will not be

initiated by RPS if a power issue exists.

 Remote update will not be executed if the

control panel is armed.

2.1.2 Automation/Integration Protocol

 GV4 Series c

ontrol panels allow Automation

software access to new GV4 features. These

enhanced commands allow Automation

software to connect to a control panel to

query the panels alarm status, sensor status,

as well as manage some user credential

information.

 The GV4 Series control panels restrict

Automation access to panel configuration by

limiting read/write commands to user

passcodes, authority levels, keyfob IDs, Sked

Enable, Pointís Name Text, Area Nameís Text,

etc.

 The GV4 Series control panels can support

one of three possible network communication

modules for Automation support; SDI Address

80, SDI2 Address 1, SDI2 Address 2. Only one

automation link is allowed at a time.

2.1.3 Passcode Enter Function

Authentication

 The GV4 Ser

ies supports two methods of

authentication for the operation of a

Passcode Enter Function. These methods are

passcode entry at a keypad or presentation of

a credential at a D9210C door controller.

 Any keypad can have one of the following

Passcode Enter Functions; Arm/Disarm,

1 2 3 4 5 6 7 8 9 10

Comentários a estes Manuais

Sem comentários